Forgotten password? or Not registered?

Non-Destructive Testing: An IntroductionNon-Destructive Testing: An AppreciationNDT Refresher and Recertification CoursesEddy Current Testing: Welds Level 1Eddy Current Testing: Welds Level 2Eddy Current Testing: Welds Level 3Eddy Current Testing: Pulsed Eddy Current (PEC) - An AppreciationMagnetic Particle Testing: Level 1Magnetic Particle Testing: Level 2Magnetic Particle Testing: Level 3Magnetic Particle/Penetrant: Refresher / RecertificationPenetrant Testing: Level 1Penetrant Testing: Level 2Penetrant Testing: Level 3Basic Radiation Safety (BRS)Radiation Protection Supervisor (RPS)Radiographic Interpretation Level 2Radiographic Testing Level 1Radiographic Testing: Computed Radiography Level 3Radiographic Testing Level 3Radiographic Testing Level 2Radiographic Testing: Computed Radiography Level 1Radiographic Testing: Computed Radiography Level 2Radiographic Testing: Computed Radiography Level 2 (Upgrade)Radiographic Interpretation: Computed RadiographyUltrasonic Testing: (ISI) Corrosion Mapping & Thickness Measurement Level 3Ultrasonic Testing: (ISI) Corrosion Mapping & Thickness Measurement Level 2Visual Testing Level 2Visual Testing Level 3Ultrasonic Testing: (ISI) Corrosion Mapping & Thickness Measurement Level 1Ultrasonic Testing: Level 1Ultrasonic Testing training course: An IntroductionUltrasonic Testing: Refresher / RecertificationUltrasonic Testing: Theory and PracticalUltrasonic Testing: Level 2Ultrasonic Testing, Ultrasonic Phased Array, Time of Flight Diffraction: Level 3Ultrasonic Testing: Critical Defect SizingUltrasonic Phased Array: Level 1 and 2Ultrasonic TOFD Welds: Level 1 & 2Auto UT InterpretationVisual Testing Level 1Isotope RetrievalProduct TechnologyNDT/Inspection Training

Ultrasonic Testing, Ultrasonic Phased Array, Time of Flight Diffraction: Level 3

Why attend this course?

These are guidance courses aimed at the PCN requirements for Ultrasonic Practitioner Level 3 in either welds, casting or wrought products. The main objective is to make candidates fully aware of the scope of the examination and level of knowledge required (This will also enable candidates to identify their weak subject areas). Advice will be given on any further tuition required. Candidates should ideally hold a PCN Level 2 approval in Ultrasonic Testing as a minimum and have at least 2 years experience in NDT Inspection before attempting these courses.

Course content

  • PCN requirements for Level 3 approval
  • Complementary NDT methods
  • Advanced product technology
  • Quality assurance, quality control and supervision
  • Specifications, procedures and techniques
  • Analysis of reports
  • Advanced ultrasonic testing theory and revision
  • Analysis of procedures
  • Procedure writing
  • Mock examinations

Course details

Duration: Length dependent on existing qualifications


Code:
RTO/UT11

Special note: Candidates who already hold PCN Level 3 certification in the Basic Module may opt to take the course which deals specifically with ultrasonic test information. These are ideal pre-approval courses for the PCN Level 3 Ultrasonic Practitioner examination, covering basic and main methods.

Course Enquiries

+44 (0)114 399 5720 or trainingsolutions@imeche.org  

Book Now

Ultrasonic Testing PCN Level 3:

PCN Level 3 Basic:
2017
PCN Level 3 Main Method:
2017
PCN LEVEL 3 (BASIC) IS AVAILABLE ONLINE, CONTACT US FOR MORE INFORMATION

Ultrasonic Phased Array PCN Level 3:
2017
Ultrasonic TOFD PCN Level 3:
2017

RTO/UT1 and RTO/UT3 combined fulfil the training requirements of PCN L2

Contact us

For more information about our services:

Email us

T: +44 (0)114 399 5720
F: +44 (0)114 243 0035

Our locations

facebookinstagramlinkedin

© 2016 Institution of Mechanical Engineers. IMechE is a registered charity in England and Wales number 206882